Zero Division

The BOX-ANT602 antenna is an antenna compatible with most Boxx TV products. 

Connects the BOX-ANT505 panel antenna to a receiver via the RP-SMA connectors.

Connects the BOX-ANT505 panel antenna to a receiver via the RP-SMA connectors.

Allows the Boxx Meridian to be connected to a computer for firmware upgrades and technical improvements.

Connects the Skydreams AirPaint system to a Sony RCP.

Full Telemetry RCP Extension CAT 5 Adaptor Cable.

12-pin Male (Plug) and 3.5mm Audio Jack to 12-pin Female (Socket) Lens Control Cable.

4-pin male XLR to 4-pin male Hirose cable.

8-pin male Hirose to 8-pin male Hirose cable.

3-pin Female (Socket) XLR to 3-pin Male (Plug) XLR cable.

4-pin Male (Plug) Hirose to 4-pin Male (Plug) Lemo cable 50cm.

One of most useful pieces of equipment for any microwave installation. Clamps onto poles up to 50mm in diameter and flat surfaces up to 35mm thick and can be used for permanent installation or for any fast deployment application.

To be used as a stable mounting solution if adaptable mounting unneccessary.
8mm Socket w/ 3/8" thread, 8mm thread length.

Alexa Anton Bauer Battery Plate Adaptor

Good all round short antenna with a 90 degree knuckle, allowing the operator to adjust position and polarisation of each antenna. 

The Universal Stand Adapter has a baby 5/8" (16 mm) stud with 1/4"-20 male thread on one side and a 3/8"-16 thread on the other. The round stud will fit into any 5/8" (16mm) receiver.

This bracket swivel adapter allows you to use an umbrella with the provided locking umbrella socket with shafts up to 3/8" or 9mm in diameter.

2 x 3-pin Male (Plug) XLR to 5-pin Female (Socket) Mini-XLR cable.

N-type Female to RP-TNC Female adaptor.

This whip, tilt antenna has a frequency range of 2.4GHz ~ 2.5GHz and connects via a RP-SMA male connector.

This whip, straight antenna has a frequency range of 2.39GHz ~ 2.49GHz and connects via an RP-SMA male connector.

Specifically designed for use with the Boxx Tally & Iris 2 Channel Transmitter.

Specifically designed for use with either the 818MHz or 914MHz Boxx Tally & Iris Control Receiver.

Designed for mounting on top of an Boxx Cobalt, Boxx Meridian or Boxx Zenith Broadcast Receiver. The antenna has a N-type female connector and uses ADP106 to connect to the Boxx Cobalt, Boxx Meridian or Boxx Zenith Broadcast Receiver.

Designed for mounting on top of a Boxx Cobalt, Boxx Meridian or Boxx Zentith Broadcast Receiver. The antenna has a N-type female connector and uses BOX-ADP106 to connect to the Boxx Cobalt, Boxx Meridian or Boxx Zentith Broadcast Receiver.

Can be used on either a transmitter or a receiver. Particularly useful when the transmitter and receiver are on the same ground elevation. 

Good all round omni-directional antenna. Mainly used with the Boxx Meridian Broadcast Receiver and the Boxx Zenith Transmitter.

The BOX-ANT601 antenna is specifically designed for the Boxx Atom Transmitters.

Good all round short antenna with a 90 degree knuckle, allowing the operator to adjust position and polarisation of each antenna. 

N-type Male to N-type Male adaptor.

N-type Female (Socket) to N-type Female (Socket) adaptor.

3.5mm Stereo Headphone Jack to 5-pin Mini-XLR Female (Socket) cable.

4-pin Hirose Male to 2-pin D-tap Male cable 40cm.

4-pin Hirose to 4-pin Hirose cable 40cm.

BNC to BNC cable 40cm.

RP-TNC Female (Jack) to RP-SMA Male (Plug) Adaptor.

N-type Male (Plug) to RP-SMA Female (Socket) Adaptor.

N-type Male (Plug) to N-type Female Right Angle (Socket) Adaptor.

N-type Male (Plug) to RP-TNC Male (Plug) Adaptor.

N-type Male (Plug) to N-type Male (Plug) Right Angle adaptor.

N-type Male (Plug) to RP-TNC Female (Socket) adaptor.