- No tags connected to product
Use spaces to separate tags. Use single quotes (') for phrases.
The AirPaint Wireless Camera Control System consists of two transceivers; one connected to the RCP and the other on-board the camera. AirPaint communicates through the remote input, allowing the user to utilize the standard camera Remote Control Panel to control all of the CCU functionality of the camera.
The system utilizes an advanced data modem at 900MHz or 2.4GHz with up to a 1-watt output enabling the operator great range of operation (approximately 2 miles). The system is currently working with all Sony cameras and camcorders that use an 8 pin remote connector and use the 422 data protocol, therefore, any camera that can be controlled by a RMB 150/750, RCP 750/920 can be controlled by the AirPaint.
In situations where the video shader/operator is in a truck or somewhere far away from the action, you can use the longest Sony RCP cable (330ft) and place the AirPaint control side transceiver up high or closer to the action. If the unit is powered locally you can power the RMB/ RCP up to (330ft) away. In sports or events requiring longer distances you can use Cat5 adapters and by powering both the RCP and AirPaint locally you can send the 422 data (2000ft or more) between the RCP and the AirPaint control side transceiver. This allows you to place the control side transceiver inside the stadium or wherever its performance is optimized. The camera side transceiver can be mounted with its Anton Bauer plate or can be situated anywhere on the camera rig. It can receive power either from a battery or get its power from the camera via the 8 pin remote connector.
The AirPaint system has been used for many production applications, from single camera shoots to multiple camera sporting events. It is a great tool for stedi-cam, jib arms, cable cams and aircraft rigs. AirPaint gives you full CCU control as well as start/stop and replay functions for camcorders. With its robust spread spectrum hopping frequency signal, this wireless control system gives you long distance, ultra low lag response, and uninterrupted camera control. Tally is available using the AirPaint with a Sony 1500 and CCU; with the AirPaint connected to the AUX of the RCP, when the CCU tallies, that information is sentwireless in the data stream turning on the camera tally.
The PL does not go through this system but there are plenty of good RF PL systems to choose from.
NOTE: The hire rate of the Skydreams Airpaint Full Telemetry system also includes a Boxx Tally Only System. The AirPaint transmits data only, additional systems are required for wireless video/audio transmissions.
1 x Skydreams AirPaint Transceiver
1 x Skydreams AirPaint Receiver
2 x SKY-ANT109: 2.4Ghz RP-SMA short right angle antenna
1 x SKY-ANT110: 2.4Ghz RP-SMA long right angle antenna
2 x SKY-CBL109: 8-pin to 8-pin Hirose cable
1 x SKY-CBL120: Full telemetry RCP extension cable via CAT5 set
1 x SKY-CBL121: Full telemetry RCP extension cable via XLR set
1 x ZER-CBL126: CAT5 10 metre cable
2 x ZER-CBL131: 2m figure 8 UK mains power lead
2 x ZER-CBL133: 2m figure 8 European mains power lead
2 x ZER-PS1205: 90-264Vac 50/60Hz Power Supply
Customers Also Hired
Boxx Atom System
Day Rate: £150Week Rate: £450
Boxx Atom Lite System
Day Rate: £115Week Rate: £345
Boxx Meridian Broadcast System
Day Rate: £150.00Week Rate: £450.00
Boxx Meridian Portable System
Day Rate: £150Week Rate: £450
Boxx Tally Only System
Day Rate: £40Week Rate: £120
Hawk-Woods V-lok Batteries and Charger Set
Day Rate: £50Week Rate: £150
12 Princeton Court
55 Felsham Road
London SW15 1AZ